Get it sorted out before you change builds. If I can't get it to work tonight, then I'll try switching to 128-bit WPA encryption, and set the transmission rate to auto. The IPs i'm using are different, but that should give you an idea. I've tried to match the settings as closely to my host router as possible. I noticed a new build was released today, so maybe I'll wipe everything clean again and try with that version.īTW, just should you know the wireless mode is set to wireless-G, with 128-bit WEP encryption, and the transmission rate is 54 Mbps. I gave that tutorial a try too, but I still couldn't get my bridge to connect to the host router, that's why I reverted back to the other tutorial. The bridge should connect to my host router wirelessly.
#Dd wrt v24 sp2 gb wifi ps3
Ya, my PS3 and media center should connect to the bridge using a cable. I presume you want a client bridged router, with no wireless clients, on the same subnet as the primary router? Is there a step missing from the guide? Please advise. I used the guide above successfully in all instances except with my WHR-HP-G54 and v24-sp2. I know I'm configuring the my client router properly, because the same settings work just fine with v24-sp1, and on my Linksys WRT54G2 DD-WRT v24-sp2 10/30/08 micro. The guide I've been following is this one: I've the a hard reset(30-30-30) a few times now, and I still end up with the same results. Which bridge type did you configure and which instructions did you folllow. Check that.Ģx EOC-2160 - AP 2x14dB Yagy to 450m linkĢx EOC-2160 - RP 2x17dB Panels - 2x 7Mbpsġx UBNT Bullet 2 - RP 18dB Panel - 11Mbps - 13Km link
#Dd wrt v24 sp2 gb wifi free
It could be an issue from this point of view, and that it does not provide the IP, or the DHCP is out of free IPs. WEP, WPA, etc.Īlso, do the same using the DHCP of your main AP. Try using an unencrypted link and a fixed IP for your bridge, then try with encryption. I am pretty sure you have a mistake in your configuration. Hi, here I do use the WHR-HP-G54 for our WIFI link to the main provider, and we do host servers using the repeater function using the 12307 micro-plus NEWD without any trouble. Location: Galati - RO / Kishinev - MD / Geneva - CH / Tarragona - E Kernel panic: Aiee, killing interrupt handler! The Wireless-G light on my router keeps blinking when I try to connect to the host router. The same process worked fine when I was using v24-sp1, but doesn't with v24-sp2. I following the bridging tutorial exactly as shown. I'm trying to use the WHR-HP-G54 in bridge mode. I loaded dd-wrt.v24-12307_NEWD_std on my WHR-HP-G54 and then did a hard reset(30-30-30), and it won't connect to my host router(Siemens Gigaset SE657).
#Dd wrt v24 sp2 gb wifi upgrade
Hopefully everything works when I do the upgrade to dd-wrt.v24-12307_NEWD_std. I'm reading through the Peacock thread now. The differences between 12307 and BS builds would take too long to e either 11296 or 12307. Whether you need vint or newd is also explained in the peacock thread. All of them work fine with all builds after SP1, if you configure them properly, but they are different and require different configuration. There are four different ways of creating a bridge, all of which are explained in the peacock thread. The PS3 and media center are connected by ethernet. Siemens Gigaset SE567 -> WHR-HP-G54 -> Playstation 3 and Media Center I'm trying to created a wireless bridge with my WHR-HP-G54. What are the differences between the following builds? I'm not copying files between different builds, I'm manually configuring the router using the settings mentioned in the tutorials. LOM: "If you show that you have not bothered to read the forum announcements or to follow the advices in them then the level of help available for you will drop substantially, also known as Murrkf's law." If you just want a fish, wait for a fisherman who hands them out. I'm trying to teach you to fish, not give you a fish.
What type of bridge are you trying to create? You appear to be copying config files to a different build. Read the announcements at the top of the forum before going any further.
0 kommentar(er)
